Publication:
Effect of sintering additives on the properties of alumina toughened zirconia (ATZ)

dc.citedby3
dc.contributor.authorAbbas M.K.G.en_US
dc.contributor.authorRamesh S.en_US
dc.contributor.authorTasfy S.F.H.en_US
dc.contributor.authorLee K.Y.S.en_US
dc.contributor.authorGul M.en_US
dc.contributor.authorAljaoni B.en_US
dc.contributor.authorid24476291800en_US
dc.contributor.authorid7103211834en_US
dc.contributor.authorid37067940700en_US
dc.contributor.authorid57221177925en_US
dc.contributor.authorid57215012364en_US
dc.contributor.authorid58503108700en_US
dc.date.accessioned2024-10-14T03:17:59Z
dc.date.available2024-10-14T03:17:59Z
dc.date.issued2023
dc.description.abstractThe effect of small amounts of copper oxide, manganese oxide, and stainless steel as sintering additives on the sintering behavior and mechanical properties of Alumina Toughened Zirconia (ATZ, 3Y-TZP with 20 wt% Al2O3) ceramic composites were evaluated and contrasted with that of undoped ATZ by using microwave sintering (MW) method. Green bodies were sintered at 1250�C, 1350�C, and 1500�C using a holding time of 5�min., with a heating rate of 30�C /min. In general, all ATZ samples exhibited a similar trend, as the results showed that the relative density and mechanical properties increased with increasing sintering temperature regardless of the addition of dopants. It was found that the addition of 0.2 wt% CuO, 0.5 wt% MnO2, and 0.2 wt% SS were beneficial in enhancing the densification and improving the mechanical properties of ATZ without inducing grain coarsening. The ATZ composite samples' relative density, tetragonal phase stability, microstructural evolution, Vickers hardness, and fracture toughness were revealed. The addition of 0.2 wt% CuO was the most beneficial in improving the properties of ATZ at a low sintering temperature of 1250�C since the sample obtained the highest relative density of 97%, Vickers hardness of 13.2GPa and fracture toughness of 6.5�MPa m1/2. In contrast, the undoped ATZ required a high sintering temperature to achieve comparable results to the doped samples. The ANOVA analysis revealed that the CuO-doped ATZ sample exhibited the highest significance and was the most suitable in improving both hardness (H) and fracture toughness (KIc) across all temperature conditions. This study also proved that the microwave sintering technique promotes the densification and mechanical properties of ceramic composites compared to the conventional sintering technique. Graphical abstract: [Figure not available: see fulltext.]. � 2023, The Author(s).en_US
dc.description.natureFinalen_US
dc.identifier.doi10.1557/s43579-023-00400-y
dc.identifier.epage626
dc.identifier.issue4
dc.identifier.scopus2-s2.0-85165614500
dc.identifier.spage618
dc.identifier.urihttps://www.scopus.com/inward/record.uri?eid=2-s2.0-85165614500&doi=10.1557%2fs43579-023-00400-y&partnerID=40&md5=48ebda0d8fc01c57c2925779ff94e7c8
dc.identifier.urihttps://irepository.uniten.edu.my/handle/123456789/34105
dc.identifier.volume13
dc.pagecount8
dc.publisherSpringer Natureen_US
dc.sourceScopus
dc.sourcetitleMRS Communications
dc.subjectBiomedical
dc.subjectMicrostructure
dc.subjectMicrowave heating
dc.subjectOxide
dc.subjectSintering
dc.subjectStructural
dc.subjectAdditives
dc.subjectAluminum oxide
dc.subjectCopper oxides
dc.subjectDuctile fracture
dc.subjectFracture toughness
dc.subjectManganese oxide
dc.subjectMicrowave heating
dc.subjectSintered alumina
dc.subjectVickers hardness
dc.subjectZirconia
dc.subjectBiomedical
dc.subjectCeramic composites
dc.subjectDensifications
dc.subjectMicrowave-heating
dc.subjectProperty
dc.subjectRelative density
dc.subjectSintering additives
dc.subjectSintering behaviors
dc.subjectStructural
dc.subjectVicker hardness
dc.subjectSintering
dc.titleEffect of sintering additives on the properties of alumina toughened zirconia (ATZ)en_US
dc.typeArticleen_US
dspace.entity.typePublication
Files
Collections