Publication:
Impact of static load on voltage stability of an unbalanced distribution system

Simple item page
dc.citedby4
dc.contributor.authorGunalan S.en_US
dc.contributor.authorRamasamy A.K.en_US
dc.contributor.authorVerayiah R.en_US
dc.contributor.authorid55549473300en_US
dc.contributor.authorid16023154400en_US
dc.contributor.authorid26431682500en_US
dc.date.accessioned2023-12-29T07:49:45Z
dc.date.available2023-12-29T07:49:45Z
dc.date.issued2010
dc.description.abstractStatic load which is known for three different characteristics i.e. constant power, constant current and constant impedance shows a different voltage profile because both of their real power and reactive power vary differently as the voltage varies except for constant power. This paper will analyze the impact of each load characteristic individually and also as combination on voltage stability of an IEEE 34 Bus Distribution System by increasing the load demand, and also transient analysis i.e. creating a single phase-to-ground fault i.e. on phase a and balanced three phase fault. The most suitable load to study the voltage stability is also proposed. It was found that, with constant power loads, the reactive power demand increases significantly when load real power and reactive power increases by 25%. Constant current loads and combination loads, on the other hand, the reactive power demand increases but only slightly and the demand is even lesser when with constant impedance loads. However, as the load real power and reactive power increases by 50%, constant power loads causes voltage collapse whilst constant current loads and combination loads turn out to be the next in the order followed by constant impedance loads. In transient analysis, during the single phase fault, with combination loads, phase b voltage increases drastically but only small increment observed in phase c voltage. During the three phase fault, phase b voltage is slightly higher than phase c voltage followed by phase a voltage. As comparison to combination loads, constant power loads causes lesser three phase voltages. After the fault was cleared, a smooth voltage waveform obtained in the period of retaining back to the same pre-fault voltage, however, distortions in the voltage recovering waveform seen when dynamic load included in the system. Constant power load is found to be the suitable load to study the voltage stability. �2010 IEEE.en_US
dc.description.natureFinalen_US
dc.identifier.ArtNo5697592
dc.identifier.doi10.1109/PECON.2010.5697592
dc.identifier.epage293
dc.identifier.scopus2-s2.0-79951806206
dc.identifier.spage288
dc.identifier.urihttps://www.scopus.com/inward/record.uri?eid=2-s2.0-79951806206&doi=10.1109%2fPECON.2010.5697592&partnerID=40&md5=b7dadf964c33923f6ff85d159683f427
dc.identifier.urihttps://irepository.uniten.edu.my/handle/123456789/30581
dc.pagecount5
dc.sourceScopus
dc.sourcetitlePECon2010 - 2010 IEEE International Conference on Power and Energy
dc.subjectDemand
dc.subjectDynamic load
dc.subjectFault
dc.subjectIeee 34 bus distribution system
dc.subjectStatic load
dc.subjectTransient
dc.subjectVoltage stability
dc.subjectDynamic loads
dc.subjectElectric load forecasting
dc.subjectElectric rectifiers
dc.subjectPhase comparators
dc.subjectPower quality
dc.subjectReactive power
dc.subjectSystem stability
dc.subjectTransient analysis
dc.subjectVoltage stabilizing circuits
dc.subjectDemand
dc.subjectFault
dc.subjectIeee 34 bus distribution system
dc.subjectStatic load
dc.subjectVoltage stability
dc.subjectCurrent voltage characteristics
dc.titleImpact of static load on voltage stability of an unbalanced distribution systemen_US
dc.typeConference paperen_US
dspace.entity.typePublication
Files
Collections
SCOPUS